Char 2C
French Super Heavy Tank
Meng Model | N. TS-009 | 1:35
I fatti
- Marca:
- Meng Model
- Titolo:
- Char 2C French Super Heavy Tank
- Numero:
- TS-009
- Scala:
- 1:35
- Digita:
- Kit completo
- Messo in commercio:
- 2013 Nuovo stampo
- Codice a barre:
- 4897038550418 (EAN)
- Confezione:
- Scatola rigida (apertura superiore)
- Argomento:
- Char 2C » Carri armati (Veicoli)
Insegne
Char 2C
Armée de Terre (French Army 1455-now)
- 51 BCC 93 ALSACE
1939
Light brown, Camouflage Green - 51 BCC 90 POITOU
1939
Olive brown - 51 BCC 97 NORMANDIE
1939
Olive brown
Contenuto della confezione
Plastic sprue, Fotoincisioni, Foglio di decals (applicabile con acqua)
Dimensioni:
390x250x95 mm
(15.4x9.8x3.7 inch)
Peso:
820 g (1.81 lbs)
Genealogia
Meng Model
2013
Istruzioni
Scaricare 3631Kb (.pdf)
Mercato
No partner shops available
Recensioni in-box
Revisioni esterne
Annuncio pubblicitario
Tutte le recensioni » (11 in totale)
Riviste
Tutte le riviste » (4 in totale)
Commenti
Ron Garcia
Surprisingly easy build. Not a ton of parts and large, easy to attach PE. I only encountered a few problems with the build.
The tracks. It was great that they were already cut off the sprue and snap together, but... The locking pins are understandably small in order for the track links to snap together. That caused me a problem when trying to snap the last one together as I wrapped one of the sides. The tracks have to be tight so that they don't sag off the road wheels in the front. That put a lot of strain on the pins. I had to selectively put CA glue and accelerator in spots where the links pulled apart. On the other side, the tracks came up a half link short. Absolutely no clue how this could have happened. I ended up cutting an extra link in half and adding it near the rear of the tank. It's only noticeable if you really look hard. After I had the tracks in place, even the most minor of handling would cause one of the track links to pop. I attached them at the very end of the build but before I added the exhaust system (for ease of painting).
I had at least a 4-5mm gap between part A37 and the lower hull. The part is attached in step 4 and then that subassembly is attached to the lower hull in step 10. By then, the cement was totally cured. I added a piece of sheet styrene to fill the gap. I think it was user error. There are two tabs on part A37, and perhaps I should have made sure they completely and firmly attached to the upper hull. Maybe that would have set a better angle (although I thought I did that when I attached the part in the first place).
As stated earlier, I installed the exhaust system as my last step. Painting all the parts off the tank was so much easier. However, there are many small, fiddly parts that attach behind other parts. It took longer than if I had just installed it as laid out in the instructions because it was hard to see where some of the end pieces attached. My suggestion is to leave the engine compartment off the tank, pant the exhaust system and engine compartment separately, attach all the pieces to the engine compartment for ease of viewing, and then attach the engine compartment to the tank as the very last step. The fit is perfect so you shouldn't need to do any paint touch ups.
The above comments aside, this is a really nice kit, and I'm glad I have it in my collection. For your efforts, you'll end up with a huge tank that looks impressive on your shelf. I have it near the FT-17 I recently built and it dwarfs it. Amazing how tank design exploded in just a short amount of time.
Surprisingly easy build. Not a ton of parts and large, easy to attach PE. I only encountered a few problems with the build.
The tracks. It was great that they were already cut off the sprue and snap together, but... The locking pins are understandably small in order for the track links to snap together. That caused me a problem when trying to snap the last one together as I wrapped one of the sides. The tracks have to be tight so that they don't sag off the road wheels in the front. That put a lot of strain on the pins. I had to selectively put CA glue and accelerator in spots where the links pulled apart. On the other side, the tracks came up a half link short. Absolutely no clue how this could have happened. I ended up cutting an extra link in half and adding it near the rear of the tank. It's only noticeable if you really look hard. After I had the tracks in place, even the most minor of handling would cause one of the track links to pop. I attached them at the very end of the build but before I added the exhaust system (for ease of painting).
I had at least a 4-5mm gap between part A37 and the lower hull. The part is attached in step 4 and then that subassembly is attached to the lower hull in step 10. By then, the cement was totally cured. I added a piece of sheet styrene to fill the gap. I think it was user error. There are two tabs on part A37, and perhaps I should have made sure they completely and firmly attached to the upper hull. Maybe that would have set a better angle (although I thought I did that when I attached the part in the first place).
As stated earlier, I installed the exhaust system as my last step. Painting all the parts off the tank was so much easier. However, there are many small, fiddly parts that attach behind other parts. It took longer than if I had just installed it as laid out in the instructions because it was hard to see where some of the end pieces attached. My suggestion is to leave the engine compartment off the tank, pant the exhaust system and engine compartment separately, attach all the pieces to the engine compartment for ease of viewing, and then attach the engine compartment to the tank as the very last step. The fit is perfect so you shouldn't need to do any paint touch ups.
The above comments aside, this is a really nice kit, and I'm glad I have it in my collection. For your efforts, you'll end up with a huge tank that looks impressive on your shelf. I have it near the FT-17 I recently built and it dwarfs it. Amazing how tank design exploded in just a short amount of time.
1 20 April, 20:34
Frank Krause
If you'd like to see this monster moving, have a look here:
Youtube Video
If you'd like to see this monster moving, have a look here:
Youtube Video
9 February 2014, 20:56
Progetti
31 immagini
Char 2C1:35
Char 2C
No. 93 "Alsace" 51st Bataillon de Chars de Combat
France - 1939
Progetto: Char 2C
Galleria
Tutti gli articoli » (5 in totale)