DeHavilland DH.88 Comet 'Grosvenor House'

Łukasz Gliński
Following

Christoph Kunz
Da schau ich Dir mal über die Schulter.

Robert Podkoński
Taking a seat, for sure!

Alex K
... sure!

Michael Kohl
Welcome mates. Happy to have you around.

Michael Kohl
Those familiar with the kit might have noticed the absence of the firewall. I simply lost it and decided that I will just omit it as it is invisible anyway.

bughunter
A very interesting plane! You made a good progress with another (parallel?) project 👍

Michael Kohl
Parallllllel, alternating. You name it. 😉

J35J
Great start!👀

Cuajete
Well done so far 👍

Michael Kohl
Thanks and welcome.

Nicolas
Great start.

Thomas Haberl - TH SCALE MODELS
Interesting build and very promising start - I´m in for this 🙂

Jennifer Franklin
Following

Michael Kohl
Moin zusammen Thomas und Nicolas.

Michael Kohl
...and Jennifer too, of course. 🙂

Nicolas
Interesting approach to simply sand the control surface structure in the primer. I'll keep my fingers crossed for a good result.

Denis Dogadov
As a base for the red color, you need to use yellow, then the red will be bright.If you put red on white, you will get just pink.

bughunter
Michael, using different primers for one top coat is my idea! The usage of my idea is geBIERenpflichtig! 🙂

Łukasz Gliński
Looks like you're the partial member of The Infanous Order of The Pink Primer 😋

Guy Rump
Looking good, following. 👍

Michael Kohl
@ Nicolas: I cross my fingers too. But looks like I have to do some homework before the final coat (see below 🙂 )

@ Denis: thanks for your input. I tested your suggestion on a scrab wing. With LP-7 I get a nice hue as well over white primer and pink base alike. Problem is that there is almost no difference between them. Over yellow (XF-3) the red receives a rather orange hue which I do not like for this project. But I am optimistic to finetune that and use lighter yellow or buff as base coat and see how that turns out. I'll keep you posted.

@Frank: So, se wollen erheben ne kleene GeBIER?!
Da trifft es sich ja gut, dass mein diesjähriger Adventskalender aus 24 Flaschen feinem fränkischen Bier aus 24 verschiedenen Brauereien besteht. Es wird mir eine Freude sein, ein-zwei-drei mit Dir zu teilen - in N?! In M?! Gruß 🙂

@Lukasz: I applied, but as PartPrimerer I am only allowed into the Entree so far. Full membetship pending. 🙂

Welcome Guy

Denis Dogadov
Yes, I will be interested in what your red color will turn out to be. I recently painted small parts red, but there was a noticeable difference in color, depending on the color of the soil. Perhaps your LP-7 is better.

Michael Kohl
I tested a couple of base coat variations for LP-7. A nice combination in my eyes is achieved when using Mr. Hobbycolor H413 yellow as base for the darker areas and pink (Tamiya X-17) for the lighter ones. But that would have meant to redo the whole base paint. So I stuck to my combination and mourned the loss of contrast.

Mark Sherwood
Looks good to me Michael. 🤘🥸👍

Cuajete
Me 2! 👍

Jennifer Franklin
That is a gorgeous colour red

Christoph Kunz
I say the same as Mark and Jennifer. 👍

Łukasz Gliński
Add some white today and it will be perfect Xmas gift just in time 😋

Jennifer Franklin
There's the white! Perfect Xmas gift.

Jakub Biganovsky
Really great job. I appreciate your approach.
I didn`t test different base color. I used GS Aquarius H23 at first piece at black surfacer, and it wasn`t fine. I will use gloss yellow at 2nd piece.
How did you do such perfect wing bottom side. It looks really nice. I had relatively big gap there and some residual step although I precisely brushed big material layer out from both wing half. Maybe, the used glue did a step at the end.
I thing, that this, wings bottom, is weakest part of this model although, as you ar writing, engine nacceles also need some attention.

Bernhard Schrock
A nice red! 🙂

Michael Kohl
Welcome mates and thanks for your encouraging and funny comments. Bottomline I am quite happy with the shade of red. I just haven't made up my mind about how gloss it should appear finally. If I would have had access to a cutter I would have scanned the bigger decals and cut masks for painting the letters.
Now what's left are the tail skid and a few bits and pieces at the wings and the stabiliser.

@Jakub: wing assembly requires some scraping and dry fitting. With super thin cement I didn't encounter any issues afterwards. But there still remains a considerable gap towards the flaps and ailerons which I filled with super glue.

Mark Sherwood
By Gum. That's a lovely looking aircraft. Kudos Michael. 🤘🥸🤟

Robert Podkoński
Looks beautiful already, Michael!

J35J
Almost there! Great build & paintwork👍🏻

Michael Kohl
Thanks mates. Let's see whether the year is still long enough to finish the plane.

bughunter
Nice 👍
Regarding the cutter - you know I can always help here! If you still want to do it may another mate can scan the decals ... or next project.

Cuajete
Fantastic job. Very nice result. Great!
Congrats!

Zbynek Honzik
Great job! I like it very much, Michael. 👍

Jennifer Franklin
I agree with everyone; great job, nice result, and I like it very much.

Rui S
I like it, a Lot 👍

Michael Kohl
Thank you all for sneaking in.
Couldn't finish it last year, so might be the first to be completed this year.
Wish you all a lot of happy modelling in 2025.