Russian 1S91 SURN Kub Radar
Trumpeter | No. 09571 | 1:35
Fapte
- Marca:
- Trumpeter
- Titlu:
- Russian 1S91 SURN Kub Radar
- Număr:
- 09571
- Scară:
- 1:35
- Tip:
- Kit complet
- Eliberată:
- 2019 Instrumentul nou
- Cod de bare:
- 9580208095714 (EAN)
- ambalare:
- Casetă rigidă (deschizător de vârf)
- Subiect:
- 2K12 Kub » Artilerie autopropulsată (vehicule)
Conținutul cutiei
Dimensiuni:
450x290x80 mm
(17.7x11.4x3.1 inch)
Greutate:
760 g (1.68 lbs)
Cronologie produs
Trumpeter
2019
Instrucțiuni
Descarca 16604Kb (.pdf)
Piata de desfacere
No partner shops available
In-box recenzii
Recenzii externe
Link rupt David's Modellbaukeller
Comentarii
Vesa-Pekka Palmu
The kit is pretty good, but there are ejector pin marks that need to be dealt with, and some of them are in annoying places to clean. The tracks are link-and-length and also have pretty deep ejector pin marks, on each individual link and few on each length piece, would recommend getting the SA-6 Kub tracks as an aftermarket part.
The kit is pretty good, but there are ejector pin marks that need to be dealt with, and some of them are in annoying places to clean. The tracks are link-and-length and also have pretty deep ejector pin marks, on each individual link and few on each length piece, would recommend getting the SA-6 Kub tracks as an aftermarket part.
1 6 November 2021, 09:56
Vesa-Pekka Palmu
And now that I remember I also ran into some fit issues with the hatches on the hull and had to do some slight modifications to one hatch and PE hinges to get them to fit.
And now that I remember I also ran into some fit issues with the hatches on the hull and had to do some slight modifications to one hatch and PE hinges to get them to fit.
6 November 2021, 10:00
Vesa-Pekka Palmu
So check the fit of all hatches before gluing any of them in place.
So check the fit of all hatches before gluing any of them in place.
6 November 2021, 10:00
Treehugger
Pin ejector marks, may be easily fixed, by the following method, which is my favourite: Use Vallejo putty in a hole, then top it like soft ice cream (so that it sticks upwards cancelling any shrinking of the putty as it dries). Wait some time, then use a blade to cut the top flush with the surface, or close enough, then let it dry some more, then maybe sand the surface clean (then the putty should have gone hard after some hours, or a day).
Pin ejector marks, may be easily fixed, by the following method, which is my favourite: Use Vallejo putty in a hole, then top it like soft ice cream (so that it sticks upwards cancelling any shrinking of the putty as it dries). Wait some time, then use a blade to cut the top flush with the surface, or close enough, then let it dry some more, then maybe sand the surface clean (then the putty should have gone hard after some hours, or a day).
6 November 2021, 11:12
Galerie
Toate articolele » (11 in total)
Material de referință
SA-6 Gainful Launcher and Radar Vehicles
Present Vehicle Line No. G 046
Jan Horak, Frantisek Koran
2016 SA-6 Gainful in detail Soviet Anti-aircraft Mobile Rocket System
Present Vehicle Line No. G 015
František Korán, Tomáš Bouchal, Jan Horák
Toate miscarile » (6 in total)