Kitty Hawk On Stilts
1
June 11, 2023These dang ejector pin marks will be a bear to remove.2
June 11, 2023This will be a little narrower so that it will fit nicely on a counter top. Should be 23” x 48” when done. Planning to build a case as well.3
June 22, 20234
June 22, 20235
June 22, 20236
June 22, 20237
June 23, 20238
June 23, 20239
July 3, 202310
July 3, 202311
July 3, 202312
July 3, 202313
July 3, 202314
July 4, 202315
July 4, 202316
July 4, 202317
July 5, 202318
July 5, 202319
July 5, 2023lots of detail painting for next weekend 8-| These are crazy nice models in themselves. Wait till i show the picture of the fire hose and nozzle. I have them separate and won’t add to the tug till I paint them. I still can’t believe i was able to assemble them!20
July 5, 2023lots of detail painting for next weekend 8-| These are crazy nice models in themselves. Wait till i show the picture of the fire hose and nozzle. I have them separate and won’t add to the tug till I paint them. I still can’t believe i was able to assemble them!21
July 9, 2023Well after a week delay due to a couple seems showing up i have the aircraft carrier base all painted. Next up, the acrylic gel to create the waves.22
July 9, 2023Well after a week delay due to a couple seems showing up i have the aircraft carrier base all painted. Next up, the acrylic gel to create the waves.23
July 9, 202324
July 9, 202325
January 2, 202426
January 2, 202427
January 2, 202428
January 2, 2024Awesome Le’Arsenal parts29
January 2, 2024Made this fence myself with wire screen from a 60gage sieve for sifting stuff like flour when baking30
January 2, 2024Awesome Le’Arsenal parts!31
January 2, 202432
January 2, 202433
January 3, 202434
January 3, 202435
January 3, 202436
January 4, 202437
January 4, 202438
January 4, 202439
January 4, 202440
January 15, 202441
January 15, 202442
January 16, 2024What ended up taking all week was figuring out how to make the oval boat “fenders”.
After a couple failed ideas i landed on some beads that i could modify.43
January 16, 2024Then I used plastic wood putty to fill the gap. The toothpick has a purpose btw, these fenders have a rod thru them that the ropes loop thru so i’m planning to cut off the toothpick to make the rod end.44
January 16, 2024Then sand with a dremel 1st, 400 grit sanding stick, then 800 grit finish. The 2 lines ended up looking like they belonged there under primer compared to the mold lines on the real thing.45
January 16, 202446
January 16, 202447
January 19, 202448
January 19, 202449
January 19, 202450
January 19, 202451
January 19, 202452
January 19, 202453
January 19, 202454
January 19, 202455
January 19, 202456
January 19, 202457
January 19, 202458
January 19, 202459
January 19, 202460
January 19, 202461
January 19, 202462
January 19, 202463
January 20, 2024False bottom64
January 20, 2024Bondo65
January 20, 2024Glazing putty to smooth it oit66
January 20, 2024Hi-build primer!67
January 20, 2024Working on cleaning up the underside of flight deck since it will be 4” in the air and you’ll be able to see it.68
January 28, 202469
January 28, 202470
January 28, 202471
January 28, 202472
January 28, 2024Had a re-do here. This sponson didn’t sit flush with the deck. Off by 3mm at the outer edge. It just had to be fixed so i cut it loose and redid it with black CA.73
January 28, 202474
January 28, 202475
January 28, 202476
January 30, 2024How many of you have chain drilled with an 1/8” drill bit ? i have now77
January 30, 2024And after a bunch of work to line things up i cut the cord and drilled holes in the hangar bay deck and then the hull AND THEN marked the base for the linear motor holes78
January 30, 2024And after a bunch of work to line things up i cut the cord and drilled holes in the hangar bay deck and then the hull AND THEN marked the base for the linear motor holes79
January 30, 2024And after a bunch of work to line things up i cut the cord and drilled holes in the hangar bay deck and then the hull AND THEN marked the base for the linear motor holes80
January 30, 2024And after a bunch of work to line things up i cut the cord and drilled holes in the hangar bay deck and then the hull AND THEN marked the base for the linear motor holes81
January 30, 2024So here’s how it will fit up82
January 30, 2024So here’s how it will fit up83
January 30, 2024Then let’s finish this out with another crazy add … i’ve started a foc’sle because the whole bow will be open and it was just going to be too barren ? just in-process but i think it’s looking good so far84
January 30, 2024Then let’s finish this out with another crazy add … i’ve started a foc’sle because the whole bow will be open and it was just going to be too barren ? just in-process but i think it’s looking good so far85
January 30, 2024So here’s the 3/16” bar i put under the flight deck. JB Weld to set the mounts for the linear motors. In a genius moment i cut 2 of the mounts too short! And JBWeld sags until it dries after a few hours so i had to make supports to keep everything lined up … oh god wait till you see this jury rigged setup86
January 30, 202487
January 30, 2024let’s start with one of those “i just can’t stop myself” moments. We should have a hi-lift for the docks! There’s a couple in the pics i have so i went ahead and scratched a few up ? the trumpeter set i have for deck equipment had a few cabs and i added some plastrut to them!88
February 1, 202489
February 1, 2024She’s on her stilts!90
February 1, 2024She’s on her stilts!91
February 1, 202492
February 1, 202493
February 1, 202494
February 1, 202495
February 1, 202496
February 1, 202497
February 26, 202498
February 26, 202499
February 26, 2024100
February 26, 2024101
February 26, 2024102
February 26, 2024
Comentários
8 September 2024, 17:28 -
Album info
Let’s see if I can bring this idea to fruition…My plan is to use a couple linear actuators to lift the flight deck so the hangar bay can be seen clearly!