North Reef Lighthouse (Australia, 1878)

1
March 12, 2022
2
March 12, 2022
3
March 13, 2022
The construction of the lighthouse is very interesting. The base contains two separate apartments for the two lighthouse keepers (source: Wikipedia)
4
March 13, 2022
Source: Wikipedia
5
March 23, 2022
Structure of the 1st floor roof.
6
March 23, 2022
7
March 26, 2022
Roof of the 1st floor coated with 8 trapezoid shaped cardboard pieces. Plus 32 narrow reinforcing stripes. All glued with thinned white glue.
8
March 28, 2022
9
March 28, 2022
10
March 28, 2022
This time I used selfadhesive paper to create the reinforcing stripes for the side walls. Less work, less mess and no sanding& cleaning after airbrushing required.
11
April 1, 2022
Four “prebended” sidewalls in place.
12
April 1, 2022
13
April 2, 2022
14
April 2, 2022
15
April 3, 2022
I decided to install the windows AFTER completing and painting the base module. For installation from outside I attached a piece of Tamiya tape as “holder”.
16
April 3, 2022
Windows after positioning with few small blobs of white glue…
17
April 3, 2022
… after removing the tape holder. Sealing with thinned white glue at next.
18
April 4, 2022
Hart to believe that this subassembly consists 52 parts.
19
April 4, 2022
20
April 6, 2022
After airbrushing, sanding and second round of airbrushing.
21
April 6, 2022
Center part fixed temporary to the working base with 4 small blobs of thinned white glue.
22
April 6, 2022
All 16 supporting arms glued to the round walking area.
23
April 6, 2022
After removing the center part from the working base. Ready for airbrushing with dark grey. Center part ready for airbrushing off white. Result: after glueing both airbrushed parts together absolutely clean margin between dark grey and off white.
24
April 7, 2022
3 of 14 posts in place. Indeed white glue is a wonderful glue!
25
April 7, 2022
Gangway glued in place with thinned white glue.
26
April 7, 2022
27
April 8, 2022
Railing completed. Fortunately I decided to use 0,4 mm round rod for the railing instead wire. More flexible and easier to install.
28
April 8, 2022
Painting the white round rods in dark grey coming soon.
29
April 13, 2022
Base color dried. Any imperfections sanded with 1000 grit sanding pad smooth.
30
April 13, 2022
I had luck and found a wooden ball with nearly correct diameter (10,5 mm, should be 12 mm).
31
April 13, 2022
End finish with semimatt red.
32
April 14, 2022
A few days ago I thought that I would have to abandon the project because I produced a great mess while covering the core with 4 thin cardboard sheets.
1st step of the rescue - operation: I airbrushed more than 10 cubic centimeter 1000 Mr Color leveler.
33
April 14, 2022
Other site of the tower. The grey leveler is well visible.
34
April 14, 2022
After 2nd (thick light grey coat), 3rd (sanding with 1000 grid pad) and 4.th step (the finish coat with off white).
35
April 14, 2022
36
April 14, 2022
The very first study for the flashing circuit.
37
April 14, 2022
Flashing characteristic: 2 short white flash, divided by 15 second pause. I intend to “clenched” the sequence.
38
April 16, 2022
The CR 2032 is not able to supply the sheduled current of 10 mA. So I had to modified the circuit. Two large capacitors will be now the source for the two short pulses.
39
April 16, 2022
Batteries and the little 1/4 circle shaped board fits!🙂
40
April 16, 2022
41
April 17, 2022
5 mm white Led installed in a piece of plexiglass 10 mm rod. 3/4 of the fuel tank (remained after finishing my Decotora truck) as mounting.
42
April 17, 2022
For better handling I installed a connector for the Led supply.
43
April 21, 2022
At the same time the most complicated and important tasks in this project. At the first attempt I tried to build the lantern house of 16 sole trapezoid shaped clear sheets: I gave up🙁. At the second attempt I constructed the lantern house of one bended piece of clear material. That worked🙂.
44
April 21, 2022
10 of 16 pre colored framing of cardboard in place. I’m taking my time with this.
45
April 23, 2022
46
April 23, 2022
47
April 25, 2022
Completed in connection with original sand of Sylt (australian/german joint venture🙂.
48
April 25, 2022
49
April 25, 2022
50
May 7, 2022
51
May 7, 2022
52
May 7, 2022
53
May 7, 2022
54
May 7, 2022

Comentários

19 12 March 2022, 12:02

Hanno Kleinecke
Oho - schon losgegangen, da nehme ich mal Platz ! 🙂

13 March 2022, 09:18

gorby
Looks very interesting.

13 March 2022, 12:20

Hanno Kleinecke
Looks like you're kidding us - admit it Bernhard, this is going to become a Haunebu flying saucer, carmouflaged as an australian
Lighthouse ! Indiana Jones missed out on this one on his search for the cryistal skulls…😄

23 March 2022, 19:27

Villiers de Vos
An interesting subject.

23 March 2022, 20:34

Łukasz Gliński
Another one? I'm in!

2 April 2022, 19:59

David Taylor
As above.

13 April 2022, 18:46

Ben M
watching this

14 April 2022, 15:39

Tom ...
👀

16 April 2022, 18:29

Hanno Kleinecke
Expert approach to every aspect as usual ! I think you've reached an interesting point here : There IS a scale effect on time !
15 seconds of darkness beteween the two white flashes would have defenitely been too long to look authentic,
so your decision to shorten the sequence was absolutely the right one 👍

17 April 2022, 18:01

Bernhard Schrock
Today I finished the Australian lighthouse and I'm very happy with the result🙂 At the same time, I am almost "horrified" 🙁 to see how big it is: A little bigger than Kermorvan. Doesn't fit in a showcase. So I have to "clean out" my largest showcase in the basement. Today only some photos taken in advance with the smartphone.🙂

25 April 2022, 18:00

David Taylor
Looks great Bernhard.

25 April 2022, 18:55

Hanno Kleinecke
Very picturesque ! What a pretty Lighthouse this is.
And all the challenges you had to master left absolutely NO trace - masterclass as usual 👍. 😄

26 April 2022, 05:50

Łukasz Gliński
What a beauty!

26 April 2022, 07:24

Zbynek Honzik
Beautiful job! 👍

1 May 2022, 20:15

Hanno Kleinecke
Picture #50 : Model or the real thing ? Indistinguishable ! 👍

7 May 2022, 18:41

Project info

North Reef Lighthouse (Australia, 1878)

54 imagens

1:72

Concluído

1:72 North Reef Australian Lighthouse 1878 (Shipyard ML:006)

Todos os álbuns

Ver todos os álbuns »