Avia C.2B1

1
August 26, 2017
The inspiration.
2
August 26, 2017
The rear control panel installation is problematic, as it sits too high and too far forward.
3
August 26, 2017
I decided to reposition it down a bit and further back, to clear the resin piece (PUR 6) that spans the cockpit at this location.
4
August 26, 2017
Piece of styrene did the trick.
5
August 26, 2017
The control pedals in the rear cockpit sit way too high also. I did not fix this, but it's a consideration when building an open cockpit.
6
August 26, 2017
Interior was primed with Mr. Surfacer and then airbrushed with Testors Acryl RLM66. Enamel wash was followed by drybrushing with lighter grays.
7
August 26, 2017
Completed cockpit. The kit comes with a nice PE set that adds needed detail to the cockpit.
8
August 26, 2017
I did not use all PE parts supplied: I left the pedals as is, and did not add any detail to the cockpit walls (closed canopy will prevent seeing most of this anyway).
9
August 26, 2017
10
August 26, 2017
The part A18 representing the engine is not tall enough. I added a shaped styrene block to the bottom to ensure that the propeller shaft lines up correctly with the front fuselage section, part A17.
11
August 26, 2017
Undercarriage assembly was straightforward and per instructions.
12
August 26, 2017
Mr. Surface primer was followed with Testors Acryl RLM02, washed with dark enamel and drybrushed with whitened RLM02,
13
August 26, 2017
Assembling the fuselage and the wings. No issues here.
14
September 13, 2017
There is a gap between the fuselage and the horizontal stabilizer (nothing a bit of putty can't fix).
15
September 13, 2017
A propeller jig is needed to assemble the propeller. The propeller hub is resin (2 versions are supplied with the kit, as are 2 propeller blade styles).
16
September 13, 2017
The resin engine scoops supplied with the kit are too stiff to conform to the fuselage. I replaced them with shaped styrene.
17
September 13, 2017
There are a number of fiddly PE parts that are butt-joined to the wings. Small pins left on the PE parts, together with mating holes in the plastic, would have made for a much stronger joint.
18
September 13, 2017
..more fiddlies…
19
September 13, 2017
Cockpit is ready for the canopy. Conopy fit was very good. I dipped it in Future and glued it on using Krystal-Kleer.
20
September 13, 2017
Canopy masked using the Montex mask and Vallejo masking fluid. The Montex mask material is stiffer that the competition, and the rear section needed a bit of the masking fluid to close up.
21
September 13, 2017
Once I was happy with the prime coat (several cycles of PSR were needed), I airbrushed the panel lines with dilluted Testors Acryl Black.
22
September 13, 2017
23
September 28, 2017
All Clad 2 ALC 106 White Aluminum was airbrushed in thin coats to allow pre-shading to show through.
24
September 28, 2017
Gunze gloss coat from the can was applied the next day as base for the Mark I decals. They went on nicely and needed very short soak to come off the paper. I used the Micro Sol decal solution.
25
September 28, 2017
Testors Acryl black was airbrushed on the engine panels following required masking.
26
September 28, 2017
I used dilluted oil paint thinned with lighter fluid to highlight the panel lines and give some depth to the silver.
27
September 28, 2017
Here, the Raw Umber oil wash after application to the port wing.
28
September 28, 2017
Landing gear legs fit in a very shallow tubes, so gluing these is tricky, especially since proper positioning is required. I strongly recommned adding metal pins to strengthen the joint.
29
September 28, 2017
The space between the landing gear leg and the wheel well is too narrow for the wheel well cover: I sanded each cover until it slid into this space.
30
September 28, 2017
And here are the completed pics.
31
September 28, 2017
32
September 28, 2017
33
September 28, 2017
34
September 28, 2017
35
September 28, 2017
36
September 28, 2017
37
September 28, 2017
Splatter on the wheel covers and undercarriage is Testors Acryl Raw Umber, Red Earth, and Sand.
38
September 28, 2017
39
September 28, 2017

Comentarios

26 August 2017, 21:32

Łukasz Gliński
How come I missed this one? 🙂

27 August 2017, 06:37

Alec K
Thanks for looking Lukasz. Lots of great projects on Scalemates lately😉 Looks like you have a bunch on the bench yourself 👍

27 August 2017, 12:26

Christian Bruer
A nice start, I will take a seat to follow.

27 August 2017, 13:11

Łukasz Gliński
Indeed Alec, indeed... 🙂 Trying to get rid of SR.53 currently 🙂 But somehow I'm unable to have less than 5 open projects😉

27 August 2017, 17:21

Lost_Erik
Wonderful interior build and presentation. That engine piece, A18, was a surprise to see.

28 August 2017, 01:54

Alec K
Welcome aboard Christian 👍

@Lukasz: don't know how you manage it 🙂

@Lost_Erik: I think there will be some more surprises with this build 😄

28 August 2017, 03:03

Łukasz Gliński
Nothing difficult Alec, kind of addiction, you know😉 It happens when you can't decide😉

28 August 2017, 12:16

Alec K
I know what you mean 👍😉

28 August 2017, 12:31

Bart Goesaert
looks good so far. what is the bulge at the exterior of the cockpit?

28 August 2017, 15:54

Alec K
Thanks Bart. I believe the bulge under the cockpit on the starboard side is an optional gun camera for the gun-equipped variants.

29 August 2017, 00:13

David Andrs
I have this in my stash, but in 1:48. Have not decided if I am going to do the Czech or Hungarian version. Nice to see something different 👍

9 September 2017, 14:09

Alec K
Thanks Dave. The Hungarian version has an interesting open rear cockpit, so that would for sure be something different. I added few more pics, getting this project wrapped up.

13 September 2017, 19:00

David Andrs
Why did you preshade? I thought for NMF one starts with gloss black first then the metalics.

14 September 2017, 12:17

Łukasz Gliński
Nice progress Alec

14 September 2017, 15:29

Alec K
@Dave: Agreed, that is the accepted practice. My issue with black undercoat is that it darkens the silver, which IMHO is opposite to what I am trying to do, i.e. keep the silver light on account of the scale effect (that said, white primer may be a better choice to achieve that end). In addition, I wanted to highlight the panel lines, not possible with black base.

15 September 2017, 11:19

Alec K
Thanks Lukasz 🙂

15 September 2017, 11:20

Christian Bruer
Nice and convincing progress Alec 👍

15 September 2017, 17:55

David Andrs
Alec K: Got ya, I am curious about the end result.

16 September 2017, 06:05

Alec K
Thanks Christian.

Dave: It's almost done. The landing gear attachment needs some TLC but otherwise it's getting there.

16 September 2017, 12:09

Alec K
Finally completed - hope you enjoy.

28 September 2017, 02:23

Bart Goesaert
That's a nice one, thrown up mud is a nice detail. Did the black preshade work as planned?

28 September 2017, 04:10

Lost_Erik
Gorgeous. That silver and weathering is a fine finish, Alec.

28 September 2017, 04:32

Łukasz Gliński
Great finish, last pic is a killer! I like the weathering, not too strong. Yeah, and that emblem (my favourite in CSAF)! 👍
It's from Pardubice, isn't it? 🙂

28 September 2017, 06:03

Wim van der Luijt
Very convincing finish...

28 September 2017, 07:09

Stephan Ryll
Looking very nice 👍

28 September 2017, 16:31

Christian Bruer
Excellent work Alec 👍

28 September 2017, 19:17

Alec K
Thanks very much mates, I appreciate the kind words. I am happy with the result 👍

Hi Bart - the preshading worked well IMHO. It's a subtle effect, but it adds dept to the finish, and some "aging", which was my goal.

Lukasz - I am glad you like my digital imaging dabble (I have fun doing those). The emblem is actually that of Ostrava, where the unit flying these C-2s was based (I think it still is). Pardubice has a half-horse in its coat of arms (I guess Czechs had some horse fetish way back... 😄)

29 September 2017, 01:40

Łukasz Gliński
Interesting. I always thought (since I saw the KP MiG-15 & UTI for the 1st time) that this was Pardubice unit emblem (btw. such a restored MiG-15 stands now at Hradec Kralowe airfield). Anyway thanks a lot for the explanation.
PS. I guess all the east-Yuropean nations got this fetish at some point in time😉

29 September 2017, 06:08

Alexander Grivonev
The way you managed to put a photo of your model (pic39) over the original picture (1) is simply brilliant, almost 1:1!

30 September 2017, 10:54

Alec K
You are welcome Lukasz 👍

@Alexander: glad you like it mate 🙂

30 September 2017, 15:19

Tom
Its a beautiful model, Alec!!

30 September 2017, 15:25

Ekki
Excellent work!

30 September 2017, 16:38

David Andrs
Looks like your plan worked 👍

30 September 2017, 20:21

Danumurthi Mahendra
your work is always great pleasure to the eyes. beautiful photography too

30 September 2017, 20:58

Alec K
Thanks very much mates, your kind comments are much appreciated 👍

30 September 2017, 21:04

Hister Farjas
looks very good

16 December 2017, 19:22

Bernhard Schrock
Very seldom type and clean build! Thx for sharing.

16 December 2017, 19:37

Jens
Excellent 👍 👍 👍

16 December 2017, 20:01

bughunter
Alec, I like it 👍

16 December 2017, 22:36

Gordon Sørensen
Great looking build, Alec! The finish is fantastic!

17 December 2017, 12:17

Alec K
Thank mates for kind words and encouragement.

17 December 2017, 13:08

Album info

I decided to tackle this project mainly to try out all-metal finish using All Clad lacquers. Special Hobby released the Arado Ar-96, of which C.2 is its Czech post-WWII reincarnation, in several versions. I am planning this as an OOB build: closed canopy, no additions, just a decal option from Mark I. decal set that comes with their Arado Ar-96 title.

This turned out to be a pleasurable build. Few surprises, keeping in mind that this is a short-run kit, and some experience is handy during construction. I discuss any specifics in the accompanying pictures.

051: Avia C.2 B1

39 imágenes

1:72

Terminado

1:72 Arado Ar-96 Colours and markings with decals (Mark I MKD72002)

Avia C-2B-1

Československé vojenské letectvo (Czechoslovak Air Force 1940-1993)
1 Sqn., Air Reg. 30 Black LX-8
1949 - Trencianske Biskupice Airfield

Light aluminum finish overall

Todos los álbumes

Ver todos los álbumes »