Grumman Gulfhawk - completedZobrazit: Prezentace Mozaika Seznam 1February 20, 2019 2February 20, 2019 3February 20, 2019 4February 20, 2019On the right course again. 5February 23, 2019Fabric, stitching and ribs structure restored. 6February 23, 2019Temporary rod for holding during airbrushing. 7February 23, 2019No significant difference between the original AM and restoring/self created structure 8February 23, 20190,0 extra parts in the cockpit (will be closed) because the focus is the entire look of the Gulfhawk. 9February 24, 2019First (resin primer) and 2nd color optimated base coat in place. Orange coming soon. 10February 24, 2019I'm not a friend of resin... so I modified the kit parts myself and corrected the carburetor inlet. 11February 26, 2019 12February 26, 2019I cut too much of the cone so I had to add an additional sheet. 13February 26, 2019Slightly modified contour of the carburetor intake. 14February 26, 2019The windscreen is thin and correct but for good fit I had a lot of work. 15February 26, 2019Moveable part is too thick. Fortunately I saved the reworked kit part from the second F3F Project (for vacu forming via toaster). 16March 3, 2019 17March 3, 2019Tail wheel attachment holes should be closed. 18March 3, 2019AM R-1820 is very well designed but in my opinion the pushrods (0,9 mm) are a bit too thick. I reworked them by using 0,68 mm rod. 19March 3, 2019Thin part of the resin cone is not heigh enough. 0,6 mm thick plastik-wedge helps. 20March 4, 20191st step. 21March 4, 2019 22March 6, 2019 23March 10, 2019New oil cooler inlets in correct position (step 1) 24March 10, 201915 minutes later. Oil coolers completed. 25March 11, 2019 26March 11, 2019 27March 15, 201918 bulges in place. 1 lost, 5 remains. 28March 15, 2019Comparison between the kit resinpart and scratch build CORRECT cowling. 29March 15, 2019Alignment for the R-1820 30March 15, 2019 31March 15, 2019Painted on inside aluminum. 32March 15, 2019Engine installed in the cowling (exactly and without mess). 33March 15, 2019Ready for orange. 34March 17, 2019The asymmetrical layout of the exhaust tubes is well visible (wrong in the kit). 35March 17, 2019Self made canopy (via toaster). 36March 17, 2019 37March 17, 2019 38March 17, 2019 39March 18, 2019 40March 18, 2019Special thanks to Axel Fischer aka CADfish_models (Konstruktionsbüro Fischer) for his help by creating the 3D-printed bulges. 41March 18, 2019 42March 18, 2019 43March 18, 2019 44March 18, 2019 45March 18, 2019 46March 21, 2019 47March 21, 2019 48March 21, 2019 49March 23, 2019 50March 23, 2019 51March 23, 2019 52March 23, 2019 53March 23, 2019 54March 23, 2019 55March 23, 2019 56March 23, 2019 57March 23, 2019 58March 23, 2019 59March 23, 2019 60March 23, 2019 61March 23, 2019 62March 23, 2019 63March 23, 2019 Komentáře10 November 2024, 11:13 - Project infoGrumman Gulfhawk63 obrázky1:48DokončenoVšechna albaZobrazit všechna alba »