Dassault Etendard IVM - completed

1
July 22, 2018
Sometimes is less enough: cockpit 1:1 OOB except yellow/black thread.
2
July 22, 2018
The kit lacks two parts as inside covers for the "gun channels". You need 2 pieces of diagonal cut plastic tube and 5 minutes.
3
July 22, 2018
On more puzzle kit! Also in this time (AS 365 Pedro) the fuselage consists of 2 dozen (!!!) parts.
4
July 26, 2018
I highly recommend to attaching the both small fins to the tail BEFORE attaching the tail to the fuselage.
5
July 26, 2018
I left the clear part GP4 because this “produce” no flush windows. I intend to make each window after airbrushing from thin clear material.
6
July 26, 2018
I recommend to replace the etched parts with thin plastic (better and cleaner fit on the stabilizers). I replaced further the plastic pins with a combination of brass tube and brass rod (better and stronger fit).
7
July 26, 2018
Each position light will be attached after coloring and after airbrushing.
8
August 25, 2018
A lot of time was needed to fit the wing tips to the middle section (different thickness).
9
August 25, 2018
10
August 27, 2018
New research results: detacheable camera pod carried only in version P. Because this is an M I had to rip of this part. 🙁
11
August 27, 2018
Fortunately this worked without any major damage.
12
August 27, 2018
Another instruction mistake by Kittyhawk: the fins were mounted obviously only on the Super Etendard. I did not find any picture of my plane showing these fins. More ripping. Grumble. 🙁
13
September 1, 2018
14
September 1, 2018
15
September 1, 2018
16
September 1, 2018
17
September 1, 2018
18
September 8, 2018
19
September 8, 2018
20
September 8, 2018
21
September 8, 2018
22
September 9, 2018
23
September 9, 2018
24
September 10, 2018
25
September 10, 2018
26
September 10, 2018
27
September 10, 2018
28
September 13, 2018
29
September 13, 2018
30
September 13, 2018
31
September 13, 2018
32
September 13, 2018
33
September 13, 2018
34
September 13, 2018
35
September 13, 2018
36
September 13, 2018
37
September 13, 2018
38
September 13, 2018
39
September 13, 2018
40
September 13, 2018
41
September 13, 2018
42
September 13, 2018
43
September 13, 2018

Komentáře

3 22 July 2018, 09:44

Stefan Fraundorfer
Da bin ich natürlich wieder dabei, um den Bau eines weiteren super Modells mitverfolgen zu können.

22 July 2018, 10:48

Tom
Again a Super Maschine!!

24 July 2018, 08:33

David Funke
watching!

29 July 2018, 20:13

Oliver Peissl
Hi Bernhard, as always I´m in when you start a project!

9 August 2018, 09:38

Bernhard Schrock
Hi mates. I need some help about the carried weapons but I'm no Aeronavale expert.
On Brittmodeler I found a hint that the Etendard did not carried the included 600 l wing tanks. The weapon sprues contained a lot of parts but I'm not sure what to use.

26 August 2018, 15:38

Rene Scheiblich
I stumbled over this page, don't know if it's of particular help to your problem at hand though.

airvectors.net/aveten.html
Scroll down about a third of the page, the guy lists some loadout info there.

26 August 2018, 15:45

Bernhard Schrock
Thank you Rene. This is exactly the right website which I looked for. As a result I know now the correct course and ripped off some parts.

27 August 2018, 14:43

Rene Scheiblich
You're welcome Bernhard! 👍

27 August 2018, 16:45

Bernhard Schrock
I need some help again: the kit provides 4 clear parts for 4 cutouts on the bottom of the fuselage. The drawing show only two but IMO that were no windows but cooling gills or so (pictures 16 and 17).

1 September 2018, 09:57

Hanno Kleinecke
That would be my assumption too, even if the drawing had avery crude way of depicting clear parts, these lines look a lot more grill-like rather than glass-like.🙂

1 September 2018, 11:09

Rene Scheiblich
Yeah looks like grilles to me as well. And the old Heller IV M kit (not really sure about the accuracy of that one though!) has two grilles in that spot. exactly like in the drawing you sourced.

1 September 2018, 12:02

Bernhard Schrock
Hanno & Rene:Thank you for supporting me. Last week I finished the painting and meanwhile the decaling is completed: three days ago I received the only avilaible decal sheet of Carpena.

I discovered that there is a very big difference between the old version of Mr. Mark Setter (232) and the new version called Mr. Mark Setter NEO (234). The old version is a much better and unfortunately in Europe not available (because the EU Lösungsmittelreform 🙁🙁🙁 ) and so I ordered three bottles in Japan.

8 September 2018, 15:51

Augie
Really nice going bernhard

8 September 2018, 18:09

Rene Scheiblich
So far I haven't run into trouble with the Mark Setter Neo... And the other stuff is better? Nice!

Very tidy paintjob and decaling Bernhard.

I just happen to be looking up intel about french and british development in the 50s/60s right now... The etendard isn't far off 🙂

9 September 2018, 14:32

Bernhard Schrock
New research results. The kit contains wrong fuel tanks in wrong shape and without fins. Furthermore the instructions indicated wrong pylons: parts 80 and 81 are the correct ones.

9 September 2018, 14:43

Bernhard Schrock
Landing gear in place. It was a very tricky job: seldom seen a kit witch such a poor engineering of landing gear - alignment🙁

10 September 2018, 19:20

Glenn
Watching!

10 September 2018, 19:29

Rene Scheiblich
Got to stay on the edge with those instructions... You never know when they are a bit dodgy. Good catch!
The hydraulic cylinders seem to be glued in besides their intended mounting slot in the gearbay... But everything seems true and straight. Strange...

May I recommend the Italeri 48th scald 262 for the most perfectly done undercarriage mount? ;P

10 September 2018, 19:39

Scott Dutton
Interesting comment about NEO, wasnt aware there was a change, wonder which one Austrlia has and what the difference is. Nice job on Etendard

11 September 2018, 21:32

bughunter
Again I'm impressed of the perfect nice and clean build, so especially the last pictures are looking damn great!

12 September 2018, 17:30

Bernhard Schrock
Scott: there are very interesting news about 232. Because this product is impossible to get in Europe I bought 3 bottles in Japan (!!!). The joy was very short: first I received an info that shipping via airmail is impossible and two days later I got a second mail that it is impossible to send this product to Germany via surface mail too. Now I'm asking myself what the hell is in this bottle? I've used this nearly 10years and I'm still alive 🙂.
Yesterday I ordered a second batch of bottles in Taiwan and I'm very curious if I will get this 🙂
bughunter: thanks for saying that: I specially appreciate this compliment from you.

13 September 2018, 15:12

Bernhard Schrock
Rene; many thanks for you helpful advice. It seams that French (naval) planes are one of your specialties...

13 September 2018, 15:14

David Funke
Well done, Bernhard!

13 September 2018, 15:21

Hanno Kleinecke
Looking simply amazing, fantastic result Bermhard !

13 September 2018, 20:21