Indian Iskra
Komentáře
13 June 2018, 19:48
Maciej Bellos
While the detail of the Arma Hobby is far better than the mastercraft one, there are some fit issues, especially at the lower part of the intakes and the wing join. Nice cockpit!
While the detail of the Arma Hobby is far better than the mastercraft one, there are some fit issues, especially at the lower part of the intakes and the wing join. Nice cockpit!
24 June 2018, 17:19
Łukasz Gliński
Thanks and welcome. Maciej, I didn't find any problems with wings, however fit of both canopy parts is poor in my case, same with underside of the fuselage. But the kit is a huge improvement comparing to the ZTS kit family. Currently I'm filling some holes I found here and there, planning to start painting in few days.
Thanks and welcome. Maciej, I didn't find any problems with wings, however fit of both canopy parts is poor in my case, same with underside of the fuselage. But the kit is a huge improvement comparing to the ZTS kit family. Currently I'm filling some holes I found here and there, planning to start painting in few days.
24 June 2018, 18:14
Oleg Bogolei
have such in my stash, so waiting for continuation)
i've started this already, but was a litle bit scarrd by a quality of the model...
have such in my stash, so waiting for continuation)
i've started this already, but was a litle bit scarrd by a quality of the model...
6 July 2018, 20:28
Łukasz Gliński
Well, I don't find it that bad 🙂 The PE set is a bit tiny for my eyes/hands and there were few small fit issues mainly at the bottom of the fuselage (under the cockpit, inlet external sides and where the trailing edge meets the fuselage), but nothing scary. It's lightyears ahead when compared to ZTS/Mistercraft Iskra (built by Maciej Bellos for example)
Well, I don't find it that bad 🙂 The PE set is a bit tiny for my eyes/hands and there were few small fit issues mainly at the bottom of the fuselage (under the cockpit, inlet external sides and where the trailing edge meets the fuselage), but nothing scary. It's lightyears ahead when compared to ZTS/Mistercraft Iskra (built by Maciej Bellos for example)
7 July 2018, 09:43
Łukasz Gliński
Short update - decals treated with the Markfit Strong, cause GX100 layer made them quite thick and strong
Short update - decals treated with the Markfit Strong, cause GX100 layer made them quite thick and strong
17 July 2018, 17:37
Łukasz Gliński
Thank you, it's sad however that nobody prints the Indian decals (do you read it Techmod, Caracal and other Syharts?😉 )
Thank you, it's sad however that nobody prints the Indian decals (do you read it Techmod, Caracal and other Syharts?😉 )
1 August 2018, 11:03
Łukasz Gliński
Thx, it's already there, between the Fishbed and the Mirage from the land of Oz 🙂
Thx, it's already there, between the Fishbed and the Mirage from the land of Oz 🙂
1 August 2018, 12:00
Łukasz Gliński
Efcharisto. Still jealous about yours though, looking forward to seeing a new mask/decal set for White-Red Sparks livey in 1/72
Efcharisto. Still jealous about yours though, looking forward to seeing a new mask/decal set for White-Red Sparks livey in 1/72
2 September 2018, 20:54
Rahul Kulkarni
Very beautiful model. Nicely done. I have this in my kit. Looking forward to do it.
Very beautiful model. Nicely done. I have this in my kit. Looking forward to do it.
23 December 2018, 10:51
Łukasz Gliński
Thanks a lot. Just a hint for you: take care of the lower fuselage joint, it's quite tricky.
Thanks a lot. Just a hint for you: take care of the lower fuselage joint, it's quite tricky.
23 December 2018, 12:20